Refinishing a Pressure Treated Deck

How to stain and repair a peeling pressure treated wood deck.

We've lived here for 5 years now, and have always talked about fixing up the deck and we finally got to it (one afternoon, and two Saturdays). After researching on the web for ways to remove deck stain, and paint, I was a bit perplexed because I wasn't sure exactly what was on our old deck, which makes a difference as to how you should proceed, for both removal and applying new deck stain or new deck paint. (Sorry I seem to have messed up the layout of this article.)


This close up of our pressure treated pine wood deck, shows cracks, peeling and some wood rot. My first idea was to replace the boards. Cost would have been around $350 or so. That plan was vetoed by the budget committee. My second plan was to flip the boards over, as the under sides looked much better and the boards are 2 x 6s and only the top surfaces had issues. The deck was still very sturdy structurally, minus 2 rotting boards. In the end, the budget committee/planning board told me I had to "work quickly" with what was there. So the decision was made to fix what was there, without turning this into a lengthy project. Note: click on photos to enlarge them.


Here's a quick after shot, for a before and after comparison.


Here's a before shot of the deck.


This is a before shot looking down one side of the deck.


This is a before shot of the other side.


You can see that it was in need of TLC.

Nowadays decks are all stained, and the stain can be opaque, giving the appearance of paint. I recommend that you take a piece of your deck (a stair riser board perhaps, as I did, or a chip of your current finish) down to your local paint shop. They'll give it the look, feel, and scratch test, and might even throw a few chemicals at it to see how it reacts to identify what's currently there to determine your best next steps.


Here's a railing section where the pressure treated wood has "cupping" and popped up deck screws. Exposed to years of wetting and drying the boards swell and then shrink, pushing up screws and nails.


Here's a similar example at the corner of the railings. The cracks in the posts are typical of how pressure treated wood dries and ages. Although it doesn't look so nice, it doesn't affect the structural integrity of the deck. If you are thinking of using wood putty to fill the cracks don't. At least that what I read on the web. It seems that when the wood expands and contracts with the outside temperature, the putty will come out, or something else not so good.


Not knowing if I had paint on here or stain, I took a guess and tried stain stripper (this was before I eventually took a sample to the local paint shop). The directions have you mop it on thick and let it sit, while making sure it doesn't dry out. "Lifting" of the stain is supposed to begin after 5 to 45 minutes. I let it go for about 35 minutes, misting it every so often with the a hose. You'll need a paint tray, a stiff brush, rubber gloves, and goggles to do the job.


This a shot of the deck with the stain stripper on it. Great time to take a breather as it does it's thing.


Here's a close up of the stain remover in action. Well nothing much happened to the stain, even while working it with a stiff brush, but the deck did get a good cleaning up of mildew and algae. With not much in way of results, I began to wonder if I had paint on there instead of stain. Perhaps some bits came up, but not much for sure.


I then gave the deck a good rinse with the garden hose to remove the stripper, and started in with a 2,600 max psi pressure washer. This yielded much better results than the stripper. Anything loose (and then some) came up. I couldn't have easily removed all of the stain/paint, so I only removed what wanted to come up and then a bit more. A pressure washer can damage the wood if used too close or if you use too much pressure on soft woods like this pressure treated pine, but I didn't care much, as the surface of the boards couldn't be much worse. Above shows the results after stripping, pressure washing and drying.

A Note About Pressure Washers in The Wrong Hands
Many professional pressure washing services state on their websites that much damage can be done by pressure washing at too high a pressure. They state that they use powerful cleaners and strippers that can only be purchased through dealers that work directly with them. They state that the chemicals that home owners can purchase, at home centers, can't do the job well, and thus home owners resort to using too much pressure, which can potentially cause serious damage to their wood. Because the professionals use these powerful cleaners, they state that they only use very low pressure (in the hundreds of psi, versus thousands as I have used). I believe the above statements to be true, so if you are not comfortable with taking the risk of ruining your deck, have a professional do the work. I on the other hand only need this deck to get through a few more years as we have plans to remodel it in the future. Also, I'm a die-hard do-it-yourselfer, and I make mistakes sometimes and learn from them. I'm willing to take chances and sometimes I pay the price. So you have been warned, and professionals will be happy that I've added this disclaimer. Onwards...

You can rent a decent pressure washer at your home store, but I decided to buy a $300 model and then after using it for a few weeks, for pressure washing everything on my property, I'm planning on selling it on Craigslist. Much cheaper than renting for a few days, if I get a decent price for it. If not, hey I'm already falling in love with it... and might just have to keep it!


By the way, the pressure washing will create a mess of flying debris about 10 feet out from your deck, so you might want to throw down some drop cloths, or plastic to protect your patio or whatever. Keep in mind if you put plastic over your plants you could bake them in hot sun.


After stripping, pressure washing and drying (4 days of sunny warm weather drying), we went to town banging down every nail on the deck. Some had popped up quite a bit due to the shrinking and swelling of the wood in our variable Northern climate, and others just needed one good whack to seat them below the surface in preparation for our next step... sanding.


The great thing about doing these projects yourself is that sometimes you can justify a new tool purchase! I had a 5 inch orbital sander, but it wasn't up to this larger job. What I wanted to buy was a Makita 7" orbital sander, that the professional painters rave about online, but it has been discontinued and I couldn't find it quickly, so the best I could do was a 6" Rigid orbital sander with higher amps than the smaller sanders. This did the job perfectly. I ideally wanted 40 grit paper, but the local home store only had 60 grit (finer than 40). 40 would have done the job quicker, but the 60 was fine too. We didn't use anything finer after the 60 grit, and it all looked great. Some might want to do a resand with 100 or so.

We sanded to remove more of the stain/paint, but also to sand down some of the cupped boards and to smooth down the rough board surfaces (cracks from over time, and roughness caused by high power pressure washing removing softer grains of the wood). I also used my smaller 5" orbital sander to round the railings around the deck and on the stair rails. This really helped make the wood look in much better shape.


The railings shown earlier, that were lifting off the posts... I fastened them down with stainless steel screws. These did a nice job of sucking the railings back in place. Stainless wood screws are great for decks and pressure treated wood, but they are expensive, and even the square head type I used are easy to strip if you drive them too quickly or if you don't apply enough steady downward pressure on your screw gun. After that I used my smaller 5" orbital sander to make smoother transitions from one deck railing to another.


Here's another example of using the sander to correct warped, misaligned boards. I also rounded any other sharp deck edges where hands, feet and other body parts might prefer a softer contact.


Not too exciting, but here's what the boards looked like after stripping, power washing, sanding and then finally blowing the whole deck clean with a leaf blower. This removes all loose debris, and also some stain/paint flaps that were still holding on by a thread.


As mentioned before, I didn't know exactly what we had on the deck already (stain or paint), so I took a stair riser board off the deck steps, down to the local paint shop experts. Even they (2 workers and a few professional painters) had a hard time identifying what was on my boards. In the end it was determined that it was stain, but that it must have been applied when the pressure treated wood was still wet, as the stain was peeling off. Anyway, they recommend Sikkens opaque stain for our job.

Sure enough, this stuff was great. I took what they gave me without research other brands, and I think it was a great choice. The first coat is recommended a primer and then Sikkens recommends a second coat. Well we have kids, pets, jobs, so we are one coat, one afternoon stainers. So one coat it was, and wow, what great coverage, and it did a great job of filling and smoothing much of the smaller surface cracks in the deck boards. I mopped it on fairly thickly in order to get it down into the cracks, and then smoothed out the surface.

The color department (shown wearing overalls above) wisely decided to go with a color similar to what we had previously in order to get away with one coat, and if we missed a spot, nobody would be the wiser. I never really liked the gray, but hey, you have to pick your battles, so gray it was, again...


Here's a close up of the Sikkens stain on the deck in their "satin" finish. Once I saw the outcome I was so glad that "the planning committee" made me stick with the existing boards. The deck is smooth, splitter free, and looks great! Time will tell how it holds up under heavy traffic, and our harsh weather. I'll have to update this later this summer, after use. Click on this or any photo for a closer view.


Even the railings looked and felt great to the touch with the rounding I did with the sander and with the new thick stain on.


Here's what was a misfitting railing joint, now looking much better.


As mentioned earlier I had 2 rotten boards. This was one of them. Ideally I would have replaced them before the other work, but long story short, I did them after. First I tried using a hammer from underneath to pop them up (that's why you see wood debris kicked out of the rotten section. That didn't work so well, as the boards were tucked under the siding at the house, and under the railings on the other end. Out comes the saw! I love to have the right tool at the right time.


I cut the board in the middle and pried it up. You can see the 2 halves on the railing above. The photo that is 5 photos up, has the new board in place (look for the nicer piece right in the middle). I used stainless steel screws to put it in place after sanding and staining it in the workshop. I was lucky and had a few pieces of 2 x 6 pressure treated pine that had been drying out for about 2 years. So they were ready for stain and installation right away.


And here now is the finished result. We are all happy with it, including our young kids who will no longer be getting splinters, and it's no longer the deck we have to be embarassed about when guests are over. It's done and ready for summertime.

I guess one main point of this article is that if you think your deck boards are shot, they might not be. If they are structurally sounds (no rot, stable and secure) then they may just need a facelift.

From a few feet out, you might even think we have Trex! But when you get closer you know it's the real thing, not some cheesy plastic imitation. There is nothing like real wood to me, even if it does requires TLC from time to time.


Both cat and dog agree the new deck is better!

Resources
To come soon.

Products, Materials and Tools I Used (in progress)
Drop Cloth
Water Hose
BEHR Premium Stain & Finish Stripper No. 64
For stripping: Googles, Rubber gloves, Stiff brush with handle, Paint tray
Husky 2600 PSI, Gas Pressure Washer
Hammer
Grip Rite Stainless Steel Wood Screws
DeWalt 1/2 In. Compact 18 V Compact Drill
RIDGID 6 In.VS Dual Orbit-random Sander
DeWalt 5 In. Heavy Duty Random Orbit Sander
60 grit sandpaper for sanders
Leaf blower - Toro Electric Ultra Blower
Sikkens Rubbol Solid DEK
Brushes, Paint trays
Beer, and inspirational music


My Standard Disclaimer: This is what I did. This does not mean this is the best way, the right way, to building code, or even safe for your needs. So you are on your own with your project. I make no promises about the information presented here. I'm just a do-it-yourselfer, not a professional at all, sharing my story. So if something goes wrong with your project, you are on your own. Good luck, and have fun!

All content and photos, copyright 2009, Dover Projects
_____________________________________________________________
My Other Articles

41 comments:

  1. Peter,
    That was a great article! I'm faced with a similar problem. I finished my redwood deck in October & then it rained before the cure was finished! Now it looks like patches of mold under the finish - but it isn't. The Manufacturer said don't sand, just use their stripper but it will not remove the layers of previous finish. Guess I'll have to sand.
    Will

    ReplyDelete
  2. You mean you didn't like the patches of mold look? (joke). Thanks for commenting and all the best with with your deck!--Peter

    ReplyDelete
  3. I am about to re-stain a deck which was originally painted with a dark (almost Jacobean) semi transparent stain. Pressure washing the deck has caused some streaking of the original stain. Would a lighter semi transparent color (wife's choice)do an adequate cover job? My thinking is that I will have to use either a solid color or a semi transparent equally as dark or more as the original stain. Appreciate your comments.

    ReplyDelete
  4. I would think you are right, but you could buy a quart and try her color out, somewhere not too noticable.--Peter

    ReplyDelete
  5. This is Saturday morning and my 12 x 20 deck has all the boards turned over( it took two weeks). I was just trying to replace some screws which had backed up. I found that most of the screws we ready to break or whatever. Your article has given hope that I save the 20 year old deck without going to new boards or tex.

    ReplyDelete
  6. Nice job Dave! How did it work out, turning the boards over? One thing I wondered about was whether the boards, which cup downwards on my deck no, would cup up after flipping, leaving places for pooling water and toe catchers. Any other insight for those thinking about flipping their deck boards?--Peter

    ReplyDelete
  7. just found your article (which is great by the way) and i must say i am now dissapointed. I have the exact same looking deck as you right down to the same color and same condition. I was hoping that when i start my project tomorrow that all the paint/stain what ever it is comes off so i can give it a nice semi transparent stain. Time will tell i guess.

    ReplyDelete
  8. Leigh, I suppose it's possible. Take a sample to your local paint experts to see what they recommend.--Peter

    ReplyDelete
  9. Peter, great article and fantastic job! I am doing the same thing right now and had two questions: can you sand pressure treated lumber and can I flip deck boards. Now, I think I will try both. Worst case, I have to replace the boards later anyhow. Hey, thanks for taking the time to document your job and make it available to us! Mike.

    ReplyDelete
  10. Peter - Thanks for sharing. I have stripped the deck with Behr stripper and pressure washed it. Next I need to sand and stain. It is a big wrap around deck. About 1500 sq ft. I faced some of the same issues regarding trying to determine the type of stain/paint, wood, etc. Pictures and text are a great help to the DIYer. I may have to turn the job over to a professsional becasue I am running out of time (only Weekend work) and my HQ is running out of patience.
    AJ

    ReplyDelete
    Replies
    1. hi AJ

      how much did it cost you in labor and materials to do your 1500 sq feet deck ?

      also, did any boards needed replaced?

      please let me know

      thanks
      olga

      Delete
  11. Peter,
    How old was your decks wood when you did this? My house was built in '85. I don't know when the deck was built but if I assume the same year, that would make it 24 years this year. My boards look a lot worse than yours...not rotten but dry and very cracked. I'm afraid that a stain will be too thin and that maybe I should use a paint this time. I know the last time it was stained it was sprayed on with an opaque stain because the last owner left some in the storage building. Was your stain thick or thin?
    Thanks,
    Paul

    ReplyDelete
  12. Cyberiankhatrr,
    Sorry not to get back sooner. I took the summer off from the computer! The stain I used was very thick and if I didn't know better, I would have thought it was paint. The coverage was excellent and we've had no peeling or wear problems to date. We did this job 5 months ago now, and it's been through our normal heavy summer traffic, complete with kids, dogs and cats, with no issues. I'm not sure really how old the deck is as we've only been here 5 years. My guess is that it's about 15 years???

    ReplyDelete
  13. Peter: my name is steve ryan. I would like to talk to you about review our product Mad Dog Primer. The care and type of work you do fits in with our high end image. Could you call me at 507-645-7431 or at steve@maddogprimer.com

    ReplyDelete
  14. Update: One year now since completion with the Sikkens stain and it still looks great. No peeling or wear! I'm impressed with the product. I'm getting a touch of rust from some of the nail heads, but that's not the stains fault.

    ReplyDelete
  15. Thanks for such a great posting. I am working on our deck now, this will help a lot. Thanks.

    ReplyDelete
  16. Great job with your deck! Thank you for posting this, I am getting ready to tackle the same project. Our deck is 15 years old and while not quite as bad it is ugly. A few years ago I put down a semi-transparent that is the worst color I've ever seen. Its peachy.....I knew I didn't like it then and I hate it even more now. I started with the deck finish remover and it is not working too well, I read somewhere that you have to sand after using so I figured I'll skip that step and go right to sanding. I bought a belt sander that I love for the hand rails, using 50 then 80 grit I'm getting the results I want. I'm worried about trying to use it on the floor boards (it's a big deck) so I'm checking rental prices for a floor sander. Not sure what I need orbital or drum. Drum sounds dangerous in the wrong hands (mine). I'll try to post back with some pictures when I'm done which has to be soon, our daughter just announced her prom group (32) is coming here for pictures. Nothing like a little pressure to get me moving!

    ReplyDelete
  17. anonymous: Sometimes a little pressure is the only thing that will get a job done. ha! I would also think you would want an orbital rental and not a drum, as the boards are most likely irregular and you can get into the dips and valleys with the orbital better. We used a 6" orbital, handheld...

    ReplyDelete
  18. We are doing the same project but have semi-transparent stain on the deck now and will re-stain with the same product. We would like to skip the sanding process and just use a deck finish remover and power washer. There is no peeling on the boards just wear spots that need refreshing. Can we safely skip the sanding part?

    ReplyDelete
  19. NEW!!! DOVER PROJECTS ON FACEBOOK! Join in with your DIY spirit! Click on the BIG blue box for "Facebook, Dover Projects" in the right column above! See you there!--Peter

    ReplyDelete
  20. We have just started the same project on our 16-year old deck. We're in the process of sanding and now I'm worried. I've been reading about arsenic warnings with the pressure treated wood. We're using goggles and masks, but the dust is every where. We have a dog that I want to keep away from it. But it will still be in the soil and plants long after we are done.

    Were any of you concerned about the arsenic and how did you keep the sawdust contained?

    ReplyDelete
  21. Anonymous: Excellent, point that I had not thought about.... Anyone want to weigh in?--Peter

    ReplyDelete
  22. Hi Peter, may we use your advice / photos / blog for advice we can supply our customers with decks that need repair or may need repair. Thank you Craig.

    ReplyDelete
  23. OMG! Your "before" pics look just like our deck does now. We used our pressure washer & bleach today, with barely any results. I happened to have a gallon of the Behr Premium stripper that I picked up last fall, so we'll start over tomorrow. Thanks for your excellent article. I used Behr opaque stain in a slate blue, so I'll use the same color again. I've heard of Sikkens, I work in an auto body shop!

    ReplyDelete
  24. Not sure how I missed these last 2 comments. Craig, sure, give me credit if you can and a link back. Thanks.

    Pat! haha. I've since gotten to know Pat very well through Dover Projects on Facebook. Sorry I missed your comment back in June Pat!—Peter

    ReplyDelete
  25. This looks great. Thanks for the info!

    ReplyDelete
  26. Great blog! I'm book marking it!

    Did you use any kind of wood filler on the boards?

    ReplyDelete
  27. Anonymous. I didn't use any wood filler to fill in the cracks. I thought about it, but after researching I was discouraged to do so. I did though test one small area where a chuck of board was missing. Now I can't remember what I used, but it was some exterior grade wood filler. So far that patch is holding well, with a small, visable gap between the patch and the board...

    ReplyDelete
  28. Peter,
    The deck looks great. Trying to create a similar look but we're having trouble finding the right gray. Do you remember what color it was from Sikkens??

    ReplyDelete
  29. Great written article Peter. However, I sanded my deck before and I had problems with slippery surface when wet.

    ReplyDelete
  30. Wish I had found this article before we bought the paint... But thanks for the great tips on the beer and leaf blower - can't have enough of the first, and have been campaining for the second for quite a while!

    ReplyDelete
  31. Our pressure-treated deck is not stained, but it is rough and splintery like yours was. We are going to refinish. After reading your piece, I have two questions. (1) if there's no stain or paint on the wood, why power wash before you sand? (2) I guess you would have mentioned it if you had, but did you just put the stain on the sanded bare wood, or did you apply some kind of wood treatment/primer product first? Thanks, Eric.

    ReplyDelete
  32. Just for whats its worth, i have a deck surrounding a pool with peeling and cracking stain. No idea what it had on it before but it was terrible. Tried to strip with BM product but gave up after doing 30sf. Went out to HD and rented a square upright sander with 30 grit sandpaper. Went over the whole deck twice, it worked like a dream. I had to do some 1800 sf of decking and thank god for the sander. Then just lightly washed off the deck and waited 2 to dry it out. Got some Sikkens and went over with two coats. I chose a custom light grey colour because the deck gets hot on summer days but looks really good now.

    ReplyDelete
  33. Great article thank you! My wife and I just recently stripped the deck and are 80% done sanding it down.

    Once we find a few days of sunny weather we start the stain!

    ReplyDelete
  34. Hi

    I live in the NW and my deck looks like your orginal deck. I have a pressure treated wood (has the staple looking holes.) Each time I try using a solid base arlyic stain it flakes/peels off within a year.

    Now it has been a couple of years since you have stained your deck. Can you please provide an update on the wear of Sikkens. Or can you please post a picture of what the deck currenty looks like.

    Thanks

    ReplyDelete
  35. Old thread, but I just followed the instructions, and was able to re-do my deck for 1/10th of the cost of replacement, and it only took 2 afternoons.

    THANKS!

    ReplyDelete
  36. Thanks to all the great blogs and step by step articles(like this one). Because of these I have found a great stain called Defy it comes highly recommended on quite a few blogs. the first time I stained my deck I didn't do my home work and I used a stain that is rated one of the worst 3 stains and I didn't prep my deck right, but this time I have researched all the different stains and how to prep your deck right. THANKS to all the great people that put there own experience's out there for the rest of use :-) keep up the great blogs.

    ReplyDelete
  37. Thanks Peter. I am in the midst of a project almost identical to the one you undertook. My deck looks exactly like your "before" picture. I have pressure washed the deck and am ready to sand it down. One question I am stuck on: I am really confused after spending hours on the internet trying to learn the best most durable covering for a weathered pressure treated deck. Some reviews give Sikkens a great rating, others really trash it. Some recommend water based and some recommend oil based. Any suggestions?

    ReplyDelete
  38. Doesn't pressure treated wood contain arsenic?

    ReplyDelete
  39. Years later .... How has that stain held up? Any regrets?

    ReplyDelete
  40. I really wish the poster would come back and answer that too. I would love to know how that product held up. Its expensive but if its worth it then I would buy

    ReplyDelete

Please leave your questions or comments here. I love to get feedback. You can do so without an account or user names and passwords, etc. Just select "Anonymous" next to "comment as". Thanks!--Peter